澳门尼斯人手机网站-澳门尼斯人娱乐场

住友澳门尼斯人手机网站,弗兰德澳门尼斯人手机网站,SEW澳门尼斯人手机网站,澳门尼斯人手机网站-澳门尼斯人娱乐场-澳门尼斯人手机网站-澳门尼斯人娱乐场 设为首页 - 加入收藏 - 技术博客 - 网站地图
   齿轮马达
RR系列同轴式斜齿澳门尼斯人手机网站
RS系列斜齿轮-蜗轮澳门尼斯人手机网站
RK系列斜齿-螺旋锥齿轮澳门尼斯人手机网站
RF系列平行轴斜齿澳门尼斯人手机网站
   行星澳门尼斯人手机网站
RP系列行星澳门尼斯人手机网站
   重载齿轮箱
RHB工业齿轮箱
RM系列大型工业减速器
   高速齿轮箱/增速箱
R高速齿轮箱/增速箱
   风电齿轮箱
R风电齿轮箱
   三相异步电动机
R三相异步电动机
齿轮澳门尼斯人手机网站箱体出现渗漏油的原因及解决办法

齿轮澳门尼斯人手机网站箱体出现渗漏油是企业生产过程中较为常见的问题,同时也是设备管理工作中重点关注的问题。澳门尼斯人手机网站出现漏油,不仅会造成环境污染、油品浪费、腐蚀等,更重要的是一旦少油、断油齿轮啮合面磨损加剧,进而发生咬焊或剥离,导致重大设备事故。但是如此重要的设备问题及管理隐患为什么长期以来得不到有效的解决,其原因自然有多方面,但技术缺失、落后仍是主要原因

It is a common problem in the production process of the gear box that the oil leakage occurs, and it is also the key problem in the equipment management. Speed reducer leakage occurs, not only will cause environmental pollution, waste oil and corrosion, it is more important if less oil, oil cut-off gear meshing surface wear, and then bite welding or peeling lead to major equipment accident. However, such an important equipment problems and management problems have not been solved for a long time, there are many reasons, but the lack of technology is still the main reason behind

由于澳门尼斯人手机网站箱体是金属,不像塑料那样能实现无缝,所以澳门尼斯人手机网站上下箱体剖分面渗漏油都是澳门尼斯人手机网站漏油较常见的现象。其主要原因就是结合面贴合不够密封,存在间隙;亦或者是结合面表面粗糙;还可能是箱体结合面连接螺丝拧得不够紧等。这种情况下可以采取密封胶密封的方法处理,用密封胶涂在结合面上,由其产生的粘合力,将两结合面胶结在一起,这样就能有效的堵塞泄露缝隙。由于液态密封胶是胶稠体、能将结合面凹陷填平,对结合面具有良好的粘附力,紧固后,液体密封胶行程均匀的薄膜从而保证良好的密封效果。

Due to the reduction of the chassis body is a metal, not as plastic as to achieve seamless, so the upper and lower parts of the reducer surface leakage of oil are reducer oil leakage is more common phenomenon. The main reason is that the joint surface is not enough seal, there is a gap; or is the surface of the joint surface is rough; may also be the body of the joint surface of the screw is not tight enough. In this case, the sealant can be used to seal the method of treatment, with sealant coated on the surface, the adhesive force generated by it, the two bonding surface together, so that it can effectively plug the leak gap. Because the liquid sealant is gel body, can be filled with depression, has good adhesion, with the mask after fastening, thin film liquid sealant stroke uniform so as to ensure good sealing effect.

处理步骤:

Processing steps:

1、预先工作、清洁:将密封面上的油污、水、灰尘或锈等杂物清除干净,同时进行研磨,使结合面的间隙小于0.1mm。

1, pre work, clean: the sealing surface of oil, water, dust or rust and other debris clean, while grinding, so that the gap between the surface is less than 0.1mm.

2、涂胶:在两密封面上各涂0.1mm左右的胶层,胶层要覆盖整个结合面。

2, in the two sealing surface coating: the coating layer is about 0.1mm, the layer to cover the entire surface.

3、干燥:对溶剂型密封胶需干燥3~5分钟,带溶剂挥发后,即可扣盖。

3, dry: solvent type sealant to dry for 3~5 minutes, with solvent evaporation, you can buckle.

4、紧固:结合面的连接螺栓预紧力越大,密封性越好。同时应保证整个结合面上压紧力均匀。

4, fastening: joint surface bolt tightening force is greater, the better the sealing. At the same time to ensure that the entire binding force on the uniform surface.


日期:2017/2/4 14:49:14
咨询QQ
点击这里给我发消息

澳门尼斯人手机网站|澳门尼斯人娱乐场

XML 地图 | Sitemap 地图